Home > Glossary Item > dump1090

dump1090

Dump 1090 is a Mode S decoder specifically designed for RTLSDR devices.

-----------------------------------------------------------------------------
|                        dump1090 ModeS Receiver         Ver : 1.10.3010.14 |
-----------------------------------------------------------------------------
--device-index <index>   Select RTL device (default: 0)
--gain <db>              Set gain (default: max gain. Use -10 for auto-gain)
--enable-agc             Enable the Automatic Gain Control (default: off)
--freq <hz>              Set frequency (default: 1090 Mhz)
--ifile <filename>       Read data from file (use '-' for stdin)
--interactive            Interactive mode refreshing data on screen
--interactive-rows <num> Max number of rows in interactive mode (default: 15)
--interactive-ttl <sec>  Remove from list if idle for <sec> (default: 60)
--interactive-rtl1090    Display flight table in RTL1090 format
--raw                    Show only messages hex values
--net                    Enable networking
--modeac                 Enable decoding of SSR Modes 3/A & 3/C
--net-beast              TCP raw output in Beast binary format
--net-only               Enable just networking, no RTL device or file used
--net-bind-address <ip>  IP address to bind to (default: Any; Use 127.0.0.1 for private)
--net-http-port <port>   HTTP server port (default: 8080)
--net-ri-port <port>     TCP raw input listen port  (default: 30001)
--net-ro-port <port>     TCP raw output listen port (default: 30002)
--net-sbs-port <port>    TCP BaseStation output listen port (default: 30003)
--net-bi-port <port>     TCP Beast input listen port  (default: 30004)
--net-bo-port <port>     TCP Beast output listen port (default: 30005)
--net-ro-size <size>     TCP raw output minimum size (default: 0)
--net-ro-rate <rate>     TCP raw output memory flush rate (default: 0)
--net-heartbeat <rate>   TCP heartbeat rate in seconds (default: 60 sec; 0 to disable)
--net-buffer <n>         TCP buffer size 64Kb * (2^n) (default: n=0, 64Kb)
--lat <latitude>         Reference/receiver latitude for surface posn (opt)
--lon <longitude>        Reference/receiver longitude for surface posn (opt)
--fix                    Enable single-bits error correction using CRC
--no-fix                 Disable single-bits error correction using CRC
--no-crc-check           Disable messages with broken CRC (discouraged)
--phase-enhance          Enable phase enhancement
--aggressive             More CPU for more messages (two bits fixes, ...)
--mlat                   display raw messages in Beast ascii mode
--stats                  With --ifile print stats at exit. No other output
--stats-every <seconds>  Show and reset stats every <seconds> seconds
--onlyaddr               Show only ICAO addresses (testing purposes)
--metric                 Use metric units (meters, km/h, ...)
--snip <level>           Strip IQ file removing samples < level
--debug <flags>          Debug mode (verbose), see README for details
--quiet                  Disable output to stdout. Use for daemon applications
--ppm <error>            Set receiver error in parts per million (default 0)
--help                   Show this help

Debug mode flags: d = Log frames decoded with errors
                  D = Log frames decoded with zero errors
                  c = Log frames with bad CRC
                  C = Log frames with good CRC
                  p = Log frames with bad preamble
                  n = Log network debugging info
                  j = Log frames to frames.js, loadable by debug.html

 

« Back to Glossary Index
1 Stern2 Sterne3 Sterne4 Sterne5 Sterne (Keine Votes bis jetzt)
Loading...

Über raspberry.tips

Schreibe einen Kommentar

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert.