This 3D printing cost calculator shows what a printed part really costs: filament, electricity, printer wear and failed prints. Enter a selling price and you see profit and margin per part. The second mode is a break-even calculator: it shows after how many months and how many parts sold your printer and accessories are paid off.
The cost of a 3D print consists of filament, electricity, wear and a surcharge for failed prints. A wall mount with 45 grams of PLA and a print time of 3 hours 20 minutes costs about $1.67 with the calculator’s reference values. When you sell it, marketplace fees, packaging and shipping come on top: at a selling price of $14.99, 10 percent fees and $1 of packaging, $10.82 of profit per part remains. When you reach break-even depends mostly on volume. With 20 parts sold per month, a $300 printer plus accessories is paid off after two to three months; with your own time included it takes about twice as long.
How the 3D printing cost calculator works
The calculator adds up four cost blocks and, if you want, your own time. Every input can be changed, and you can switch between US dollars, euros and pounds. Switching the currency resets the electricity and filament prices to the reference values for that currency.
| Cost block | Formula |
|---|---|
| Filament | Weight in kg × price per kg × (1 + waste in percent) |
| Electricity | Average power in watts × print time in hours ÷ 1000 × price per kWh |
| Wear & maintenance | (Printer price ÷ lifetime in hours + maintenance per hour) × print time |
| Failed print risk | (Filament + electricity + wear) × failed print rate |
| Labour (optional) | Minutes ÷ 60 × hourly rate |
| Profit per part | Selling price × (1 − fees in percent) − packaging & shipping − cost per part |
| Break-even price | (Cost per part + packaging & shipping) ÷ (1 − fees in percent) |
The first four blocks plus labour add up to the cost per part. With a selling price, the calculator derives profit, margin and the price from which the part covers its costs. The surcharge for failed prints is an approximation: a failed print usually stops after part of the print time and then costs less than a whole part. If, on the other hand, every tenth print only fails at the very end, the surcharge would be about 11 percent instead of 10.
“Share result” copies a link that contains all your inputs, so anyone who opens it sees exactly your calculation. “Save as image” creates a graphic of the result, for example for a forum or Discord. The calculator runs entirely in your browser and your inputs are not sent to the server.
What does a 3D print cost and what is left when you sell it? Five examples
The examples use the calculator’s US dollar reference values: PLA at $20 per kilogram, 5 percent waste, 120 watts, 18 cents per kWh, a $300 printer with a lifetime of 3,000 hours, 5 cents of maintenance per hour and 10 percent failed prints. For selling, 10 percent fees and $1 of packaging and shipping per part are assumed. Weights, print times and selling prices are example values.
| Part | Weight | Print time | Print cost | Selling price (example) | Profit per part | Margin |
|---|---|---|---|---|---|---|
| Cable clips, set of 10 | 12 g | 45 min | $0.42 | $6.99 | $4.87 | 70 % |
| Wall mount | 45 g | 3 h 20 min | $1.67 | $14.99 | $10.82 | 72 % |
| Raspberry Pi case | 55 g | 3 h 30 min | $1.93 | $11.99 | $7.86 | 66 % |
| Decorative figure | 60 g | 4 h | $2.14 | $9.99 | $5.85 | 59 % |
| Drawer organizer | 110 g | 5 h 30 min | $3.58 | $12.99 | $7.11 | 55 % |
For the wall mount, $0.95 goes to filament, $0.50 to wear and maintenance, $0.07 to electricity and $0.15 to the failed print risk. It would cover its costs from a selling price of $2.97. The high margins only hold as long as you do not count your own time, though: ten minutes for slicing, post-processing and packing at $25 per hour cost $4.17 per part and halve the profit on the small parts.
3D printer power consumption: an overview of the figures
The rated power on the type plate says little about consumption while printing. It describes the maximum the power supply and heated bed can draw. The printer only reaches that peak while heating up; after that, nozzle and bed merely hold their temperature and the power drops considerably. For the electricity cost, the average over the whole print is what counts. The following table contains the values behind the “Your printer” selection in the calculator, each with its source.
| Printer | Design | Avg. printing (PLA) | Heat-up | Standby | Source |
|---|---|---|---|---|---|
| Bambu Lab A1 mini | bed slinger | 93 W | 135 W | 7 W | china-gadgets.de, 11/2025 |
| Bambu Lab A1 | bed slinger | 120 W | 896 W | 5 W | igor’sLAB, 08/2024 |
| Bambu Lab A2L | bed slinger | 135 W | 920 W | 5 W | china-gadgets.de, 07/2026 |
| Bambu Lab P1P | CoreXY | 110 W | n/a | 5 W | Bambu Lab Wiki, 10/2026 |
| Bambu Lab P1S | CoreXY, enclosed | 120 W | n/a | 6 W | igor’sLAB, 10/2023 |
| Bambu Lab P2S | CoreXY, enclosed | 200 W | n/a | 8 W | Bambu Lab Wiki, 10/2026 |
| Bambu Lab X1 Carbon | CoreXY, enclosed | 105 W | n/a | 9 W | Bambu Lab Wiki, 10/2026 |
| Bambu Lab H2D | CoreXY, enclosed | 220 W | 1732 W | 26 W | igor’sLAB, 12/2025 |
| Bambu Lab H2S | CoreXY, enclosed | 200 W | n/a | 26 W | Bambu Lab Wiki, 10/2026 |
| Prusa MK4S | bed slinger | 80 W | n/a | n/a | Prusa, 10/2026 |
| Prusa CORE One+ | CoreXY, enclosed | 90 W | n/a | n/a | Prusa, 10/2026 |
| Prusa CORE One L+ | CoreXY, enclosed | 90 W | 630 W | 16 W | Prusa, 10/2026 |
| Elegoo Centauri Carbon | CoreXY, enclosed | 152 W | 1050 W | 5 W | china-gadgets.de, 12/2025 |
| Elegoo Neptune 4 Plus | bed slinger | 153 W (PETG) | 759 W | 16 W | own measurement, 09/2026 |
| Elegoo Centauri Carbon 2 Combo | CoreXY, enclosed | 110 W | 887 W | 8 W | drucktipps3d.de, 06/2026 |
| Elegoo Neptune 4 | bed slinger | 160–190 W | 330 W | 11 W | igor’sLAB, 08/2023 |
| Elegoo Neptune 4 Pro | bed slinger | 124–192 W | n/a | n/a | thephonograph.net, 04/2024 |
| Elegoo Neptune 4 Max | bed slinger | 200–250 W | n/a | n/a | GitHub PeterVRC, o. D. |
| Elegoo Neptune 3 Pro | bed slinger | 60–70 W | 300 W | n/a | the3dprinterbee, o. D. |
| Creality Ender-3 V3 KE | bed slinger | 141 W | 375 W | 6 W | china-gadgets.de, 11/2024 |
| Creality K1 | CoreXY, enclosed | 100 W | 370 W | 20 W | 3DPrintBeginner, 06/2023 |
| Creality K1C | CoreXY, enclosed | 144 W | 400 W | 10 W | game2gether, 04/2024 |
| Creality K2 Plus (Combo) | CoreXY, enclosed | 249 W | n/a | 25 W | china-gadgets.de, 04/2025 |
| Creality K2 Pro (Combo) | CoreXY, enclosed | 151 W | 977 W | 13 W | igor’sLAB, 08/2026 |
| Creality Hi Combo | bed slinger | 166 W | n/a | 11 W | china-gadgets.de, 04/2025 |
| Anycubic Kobra 2 | bed slinger | 163 W | 299 W | 9 W | china-gadgets.de, 05/2023 |
| Anycubic Kobra 3 (Combo) | bed slinger | 205 W | 398 W | 20 W | igor’sLAB, 09/2024 |
| Anycubic Kobra S1 (Combo) | CoreXY, enclosed | 180 W | 1050 W | 16 W | igor’sLAB, 04/2025 |
| Anycubic Kobra 3 V2 Combo | bed slinger | 180 W | 700 W | 8 W | Notebookcheck, 07/2025 |
| Sovol SV06 | bed slinger | 108 W | n/a | n/a | the3dprinterbee, o. D. |
| Sovol SV07 | bed slinger | 97 W | 256 W | 9 W | china-gadgets.de, 05/2023 |
| Qidi Plus4 | CoreXY, enclosed | 245 W | 570 W | 32 W | igor’sLAB, 12/2024 |
| Flashforge Adventurer 5M | CoreXY | 130 W | 320 W | 11 W | igor’sLAB, 02/2025 |
| Artillery Sidewinder X4 Plus | bed slinger | 165 W | 390 W | 10 W | hessburg.de, 04/2024 |
Most averages are between 80 and about 250 watts with PLA. Where a review only gives a range, as for the Elegoo Neptune 4, Neptune 4 Pro and Neptune 4 Max, the table shows the range and the calculator uses its midpoint. For the Neptune 4 the measurements also differ widely: a second review arrives at an average of only 76 watts. All values are only roughly comparable: reviews measure with different test objects, bed temperatures and room temperatures. For Bambu Lab the calculator uses independent review figures where they exist. For the A1 and P1S they are 15 to 25 watts above the figures in the manufacturer’s wiki, which come from short prints. For the P1P, P2S, X1 Carbon and H2S only the wiki figures are available, and the same goes for PETG and ABS. PETG and especially ABS or ASA need more electricity because of the higher bed and chamber temperatures. Where the source gives a separate value for them, the calculator switches automatically when you change the material.
I measured the Elegoo Neptune 4 Plus myself: in September 2026 the printer ran on a smart plug with energy metering for almost two weeks. A PETG print of 4 hours 49 minutes (bed 70 °C, nozzle 250 °C) used 0.74 kWh, an average of 153 watts. With PAHT-CF at a bed temperature of 95 °C it was a steady 195 watts or so, and the calculator uses that value for ABS and ASA. The heat-up peak was about 760 watts, and idle after the print about 16 watts. There was no PLA print during the measuring period, so the calculator shows the PETG value for PLA. For a few other popular models only the rated power of the power supply is available, which is why they are missing from the list. Your own measurement is the most accurate basis anyway: a smart plug with energy metering shows the kilowatt-hours used after a typical print. Divided by the print time in hours and multiplied by 1000, that gives your average power in watts. The article Connect your 3D printer to Home Assistant shows how to monitor the printer permanently.
Break-even: when does selling 3D prints pay off?
The mode “Break-even when selling” compares the investment with the monthly profit. The investment is the printer price plus accessories. The profit per month is, for each product, the profit per unit times the units sold, minus your fixed costs. The print cost contains no printer depreciation here, because the purchase price is already part of the investment and would otherwise be counted twice. The examples use the product list the calculator starts with: 6 wall mounts, 10 sets of cable clips and 4 Raspberry Pi cases per month.
| Scenario | Investment | Profit per month | Break-even after |
|---|---|---|---|
| 20 parts per month, $300 printer plus $60 of accessories | $360 | $149.66 | 2.4 months (49 parts) |
| Half the volume, 10 parts per month | $360 | $74.83 | 4.8 months (49 parts) |
| 20 parts per month, with 10 minutes of labour per part at $25 per hour | $360 | $66.33 | 5.4 months (109 parts) |
| 60 parts per month, $999 printer plus $150 of accessories, $15 of fixed costs per month | $1,149 | $433.98 | 2.7 months (159 parts) |
The calculation shows what matters: the printer itself is paid off quickly, the bottleneck is demand. If you sell only half as many parts it takes twice as long, and if you price your own time honestly you end up with less than half the profit. So be cautious with the quantities and use the fees of your platform. The 60 parts per month in the last scenario also mean about 125 print hours, which a single printer can still handle.
Taxes are not included in the calculator. Selling regularly for profit is a business in most countries, with registration and tax obligations that depend on where you live, so check the rules that apply to you. Also check the licence of the models: many designs on Printables, MakerWorld or Thingiverse must not be used commercially. Your own designs are the safe choice. The article Raspberry Pi 5 case 3D print shows how to design one.
Reference values and sources
| Value | Preset | Basis |
|---|---|---|
| Electricity price | $0.18, €0.37 or £0.26 per kWh | US: residential average 2026 according to the EIA. Germany: household average 2026 according to the BDEW. UK: Ofgem price cap for October to December 2026. |
| Filament prices | PLA $20 or €20 per kg, other materials see calculator | The euro values are based on shop prices from Elegoo, Bambu Lab and Prusament on 4 October 2026. The dollar and pound values are rough equivalents, so enter your own spool price. |
| Marketplace fees | 10 % | Assumption. Fees differ considerably by platform and payment method; for direct sales they are 0 percent. |
| Packaging & shipping | 1.00 per part | Assumption for packaging material. Only enter what the buyer does not reimburse. |
| Supports & waste | 5 % | Assumption for parts with little support material |
| Failed print rate | 10 % | Assumption. Published figures vary between 1 and 20 percent. |
| Lifetime | 3,000 h | Free assumption, there is no reliable source for it. With a $300 printer that is 10 cents of depreciation per print hour. |
| Maintenance | 0.05 per hour | Assumption for nozzles, belts and build plates |
| Average power without a printer selected | 120 W | A value from the middle of the open-frame printers in the table above |
| Printer prices | per model | Euro prices from the manufacturers’ EU stores and 3DJake on 4 October 2026. Where no price in your currency is available, your value stays unchanged. |
As of October 2026. The calculator’s formulas are checked automatically against examples calculated by hand. If you have your own measurement for your printer or find a mistake, let us know via the contact form.
Related guides
- 3D printer filament guide: which filament for what?
- Filament storage: build a dry box
- Setting the Z-offset: why the first print fails
- Elegoo Neptune 4 Plus printable upgrades
- Raspberry Pi power cost calculator
Frequently asked questions about 3D printing costs and selling
With the calculator’s reference values, one hour of printing costs about 17 cents without filament: roughly 2.2 cents of electricity at 120 watts and 18 cents per kWh, 10 cents of depreciation for a $300 printer with a lifetime of 3,000 hours and 5 cents of maintenance. Filament comes on top and is the largest item for most parts.
Averaged over a PLA print, common printers draw between 80 and about 250 watts. While heating up, several hundred to more than 1,000 watts are possible for a short time. A ten-hour print at 120 watts uses 1.2 kWh, which costs about 22 cents at 18 cents per kWh.
First calculate the cost per part from filament, electricity, wear, the failed print surcharge and your own time. Add packaging and shipping and divide the sum by one minus the fee rate of the platform. That is the price from which the part covers its costs. Everything above it is profit before tax.
As soon as the accumulated profit exceeds the investment in the printer and accessories. With an investment of $360 and 20 parts sold per month at about $7.50 of profit per part, that is the case after two to three months or about 50 parts. If you include ten minutes of labour per part, it takes a good twice as long.
